PIC18F4539-I/ML【PDF 38/322 页】IC MCU FLASH 12KX16 EE A/D 44QFN

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录3882

34页 35页 36页 37页 [38页]39页 40页 41页 42页

PIC18FXX39

DS30485A-page 130

Preliminary

2002 Microchip Technology Inc.

16.3.5

MASTER MODE

The master can initiate the data transfer at any time

because it controls the SCK. The master determines

when the slave (Processor 2, Figure 16-2) is to

broadcast data by the software protocol.

In Master mode, the data is transmitted/received as

soon as the SSPBUF register is written to. If the SPI is

only going to receive, the SDO output could be dis-

abled (programmed as an input). The SSPSR register

will continue to shift in the signal present on the SDI pin

at the programmed clock rate. As each byte is

received, it will be loaded into the SSPBUF register as

if a normal received byte (interrupts and status bits

appropriately set). This could be useful in receiver

applications as a “Line Activity Monitor” mode.

The clock polarity is selected by appropriately program-

ming the CKP bit (SSPCON1<4>). This then, would

give waveforms for SPI communication as shown in

Figure 16-3, Figure 16-5, and Figure 16-6, where the

MSB is transmitted first. In Master mode, the SPI clock

rate (bit rate) is user-programmable to be one of the

following:

FOSC/4 (or TCY)

FOSC/16 (or 4 TCY)

FOSC/64 (or 16 TCY)

This allows a maximum data rate (at 40 MHz) of

10.00 Mbps.

Figure 16-3 shows the waveforms for Master mode.

When the CKE bit is set, the SDO data is valid before

there is a clock edge on SCK. The change of the input

sample is shown based on the state of the SMP bit. The

time when the SSPBUF is loaded with the received

data is shown.

FIGURE 16-3:

SPI MODE WAVEFORM (MASTER MODE)

SCK

(CKP = 0

SCK

(CKP = 1

SCK

(CKP = 0

SCK

(CKP = 1

4 Clock

Modes

Input

Sample

Input

Sample

SDI

bit7

bit0

SDO

bit7

bit6

bit5

bit4

bit3

bit2

bit1

bit0

bit7

bit0

SDI

SSPIF

(SMP = 1)

(SMP = 0)

(SMP = 1)

CKE = 1)

CKE = 0)

CKE = 1)

CKE = 0)

(SMP = 0)

Write to

SSPBUF

SSPSR to

SSPBUF

SDO

bit7

bit6

bit5

bit4

bit3

bit2

bit1

bit0

(CKE = 0)

(CKE = 1)

Next Q4 cycle

after Q2

↓

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式